AMSOIL PC Series Synthetic Compressor Oil is a long-life, premium
compressor lubricant based on novel, proprietary technology. It incorporates
the highest quality, thermally stable PAO synthetics fortified with
premium non-detergent additives for maximum protection at high temperatures.
It lasts up to 8,000 hours, effectively reducing maintenance
and waste oil disposal costs.
Improves Compressor Efficiency
AMSOIL PC Series Oil has low friction properties, resists
viscosity increase from oxidation and helps improve operating
Controls Foam and Reduces Wear
AMSOIL PC Series Oil contains anti-foam additives and, unlike
some other compressor oils, is anti-wear fortified. Good foam
control reduces heat, oxidation and wear. High contact regions
are protected against wear for increased compressor life and
lower maintenance costs.
Resists Water Contamination
Water from condensation builds up in compressors and can
cause unwanted oil/water emulsions that lead to rust and corrosion.
AMSOIL PC Series Oil is hydrolytically stable. It resists
acid formation, readily separates from water and is anti-rust
fortified. Water can be easily drained for simplified disposal
and increased oil life.
Resists Heat and Oxidation
AMSOIL PC Series Oil combines the inherent stability of premium
synthetic base oils with specialized anti-oxidant additives
to resist varnish, carbon and acid formation. It is formulated
to protect compressors better and last longer in service than
petroleum oils, especially during hot operating conditions.
AMSOIL PC Series Oil is an ashless, high-flash-point formulation
with very low carbon-forming tendencies that minimizes
the incidence of ignition-promoting “hot spots.” While PC Series
Oil can provide improved fire safety, it cannot be considered
AMSOIL PC Series Oil in the appropriate viscosity is recommended
for use in single and multistage rotary screw, vane,
centrifugal and reciprocating compressor crankcases and
cylinders, vacuum pumps, pressure washer pumps and other
applications such as gears, bearings, blowers, pumps and
handheld pneumatic tools. In compressor applications, drain
intervals of 8,000 hours or more can be expected under normal
operation. Drain intervals are subject to operating conditions
and maintenance practices. Monitoring by oil analysis
is recommended. For best performance when converting to
AMSOIL PC Series Oil, it is recommended the compressor
be flushed of the old oil and all filters changed prior to the
installation of PC Series Oil. If carbon deposits are present on
the internal components, it is recommended they be removed
following the compressor manufacturer recommendations.
* Consult the equipment manufacturer or AMSOIL Technical Services
for use in specific applications.
AMSOIL PC Series Synthetic Compressor Oil is compatible with
petroleum oils and most synthetic oils, seals, paints and materials,
including the following:
• Nitrogen • Hydrogen • Helium • Carbon Monoxide|
• Carbon Dioxide (dry) • Ethylene • Methane
• Propane • Butane • Propylene • Butylenes
• Natural Gas • Benzene • Butadiene
• Furnace (crack gas)
• Hydrogen Sulfide (dry)
• Synthetic Gas • Sulfur Dioxide
|• Epoxy • Oil Resistant Alkyd • Acrylic Enamel|
|• Acetal (Delrin) • ABS • Phenolic • Polyamide-imide|
• Polyamide (Nylon)
• Polycarbonate (metal covered only)
• Polyester • Polyetherimide (Nylon) • Polyimide
• Polyphenylene oxide • Polystyrene • Polysulfone
• PTFE (Teflon) • Terephthalate.
|• Fluoroelastomer (Viton) • Nitrile (Buna N)|
• Polyacrylate • TFE/P • Poly Urethane.
|Note: Not recommended for "breathing air" or refrigeration
compressors. Not recommended for use with polycarbonate
plastic that is not metal covered, PVC plastic and butyl,
ethylene-propylene or SBR rubber. PC Series Oil is not
compatible with polyalkylene glycol or silicone oils.|
HEALTH & SAFETY
This product is not expected to cause health
concerns when used for the intended application
and according to the recommendations in the
Material Safety Data Sheet (MSDS). An MSDS is
available upon request at 715-392-7101 or
on the AMSOIL Website.
Keep Out of Reach of Children.
Don't pollute. Return used oil to collection centers.
Typical Technical Properties
|Synthetic PC Series Compressor Oils||SAE 10W|
|ISO VG - ASTM D-2422||32||46||68||100|
|VK 100°C - ASTM D-445||6.1||7.3||10.5||13.4|
|VK 40°C - ASTM D-445||32.8||43.0||68.1||100.2|
|Viscosity Index - ASTM D-2270||135||132||145||133|
|SPGR - ASTM D-1298||0.8393||0.8428||0.8524||0.8550|
|Density - ASTM D-1298||6.989||7.018||7.098||7.119|
|Flash Point °C (°F) - ASTM D-92||260 (500)||252 (486)||250 (482)||262 (504)|
|Fire Point °C (°F) - ASTM D-92||274 (525)||276 (529)||276 (529)||274 (525)|
|Pour Point °C (°F) - ASTM D-97||-53 (-63)||-47 (-53)||-40 (-40)||-44 (-47)|
|Four-Ball Wear Test - ASTM D-4172 (40 kg, 1200 rpm, 75°
C, 60 min.)||0.45||0.45||0.45||0.45|
|Copper Strip Corrosion Test - ASTM D-130||1A||1A||1A||1A|
|Rust Test - ASTM D665 A & B Fresh Water and Synthetic
|Foam, ml (ASTM D-892) Sequence I, II, III Test End - and After 10 minutes settling||0/0/0||0/0/0||0/0/0||0/0/0|
|Demulsibility ASTM D-1401 [oil/water/cuff (minutes)]||40/40/0 (10)||40/40/0 (10)||40/40/0 (5)||40/40/0 (10)|